Team:UI Indonesia/Test

“INTERLAB STUDY” PAGE

Introduction

In the field of engineering, repeatable and reproducible measurements are important to obtain valid and reliable results. However, these have been proven difficult to achieve as there are differences in environmental condition of laboratories, individuals conducting the measurements, instruments being used, and other sources of variability. Eventually, this could lead to hindrance of advancements in engineering, including synthetic biology.

For past several years, iGEM Measurement Committee has been working on this issue by encouraging registered iGEM 2018 teams to participate in annual InterLab study. Since its introduction in 2014, the study has been conducted four times, making this year’s study to be the fifth one. The goal of this study is to minimize possible sources of variability in laboratory measurements and thus allowing synthetic biology to attain its full potential as a tool for improving quality of life.

InterLab study is mainly focused on fluorescence measurements as one of widely utilized protocols in synthetic biology studies. Data obtained from such measurements are often reported in different units, or processed in different methods, thereby hampering fluorescence data comparison. Hence, iGEM Measurement Committee introduces a standardized protocol for green fluorescence protein (GFP) expression level measurement. Previous studies showed that variability of the measurements can be significantly reduced by calibrating measured absolute fluorescence units of expressed GFP against known concentration of florescent molecule. However, when the procedure is carried out against a population of cells, the cell number in given sample makes great variability among measurements. This is due to the values of total cell number used to calculate mean expressed GFP per cell are obtained from optical density (OD), which is a subject to large variability.

Therefore, in this year’s InterLab study, participating 2018 iGEM teams are encouraged to help iGEM Measurement Committee in investigating whether more direct method in expressing total cell number for fluorescence calculation, such as absolute cell count or colony- forming units (CFUs), are better than OD to reduce variability in bulk measurement. We proudly announce our participation in 5th InterLab study for the first time ever, in the hope that our results may contribute to the improvements in synthetic biology. Our members contributing in this InterLab study are shown in Figure 1.

Figure 1. iGEM UI 2018 team members contributing in 5th InterLab study: (top row, left to right)

Valdi Ven Japranata, Andrea Laurentius, Ihya Fakhrurizal Amin; (bottom row, left to right)

Muhammad Ikhsan, Luthfian Aby Nurachman, Muhammad Iqbal Adi Pratama.

Materials and Equipment

Some of the materials for this study are obtained from 2018 DNA Distribution Kit. Other materials and equipment are provided by Institute of Human Virology and Cancer Biology (IHVCB), UI.

Materials from 2018 DNA Distribution Kit

•LUDOX CL-X (45% colloidal silica suspension) stock

•Microspheres (silica beads suspension) stock ~ 4.7 x 108 microspheres

•Sodium fluorescein stock

•Devices (parts in pSB1C3 plasmid backbone, all dried in Distribution Kit Plate): negative control, positive control, test device 1, test device 2, test device 3, test device 4, test device 5, and test device 6.

Materials and equipment provided by IHVCB, UI

•ddH2O

•1x phosphate buffered saline (PBS), pH 7.4-7.6

•96-well plate (clear plate with flat bottom)

•96-well plate reader (GloMax®– Multi Detection System, Figure 2). Specifications: can measure both absorbance and fluorescence, no settings for pathlength correction and temperature adjustment, has four installed filters and two customizable filter holders in six-position filter wheel, reads the samples from top of the plate

•Competent cells of Escherichia coli strain DH5α

•Luria-Bertani (LB) media, liquid and agar

•Chloramphenicol (dissolved in absolute ethanol at concentration of 25 mg/mL, when added into LB media it should be at ratio 1:1000)

•50 ml Falcon tubes

Figure 2. Our 96-well plate reader (GloMax®- Multi Detection System)

•Incubator (set at 37oC)

•1.5 ml microtubes

•Bucket with ice

•Micropipettes and tips

Methods

Safety Precautions

Figure 3. (left) Fully-worn personal protective equipment (PPE) and (right) biosafety cabinet

(BSC) used in our laboratory.

During laboratory works, we took extra precautions to minimize potential harm. We wore personal protective equipment (PPE) such as laboratory safety gowns with head cover, masks, and gloves (Figure 3, left). For procedures that require aseptic technique such as bacterial inoculation, we conducted the experiments in biosafety cabinet (BSC) to prevent contamination (Figure 3, right). We also managed every infectious waste according to our laboratory’s standard operating procedures, such as decontaminating all media used for bacterial growth with 10% sodium hypochlorite overnight before being thrown into appropriate container and autoclaving them (121oC, 20 minutes) along with other infectious wastes. In addition, to ensure validity of our results, we used same instrument settings, 96-well plates, and volumes of sample added to the plates in entire protocol whenever possible.

Part I: Calibration

Before we proceeded to Part II and III of the protocol, we had made three calibrations as follows:

•Calibration #1: this calibration is aimed to obtain a conversion factor to transform absorbance at 600 nm wavelength (Abs600) data from plate reader into comparable OD600 as would be measured with spectrophotometer due to Abs600 data are volume dependent. First, we made four replicates of LUDOX CL-X and ddH2O in 96-well plate (each well contains 100 uL volume). We then measured Abs600 of the samples and recorded them. The Abs600 data were calculated for their respective mean and then subtracted each other to obtain corrected Abs600. OD600 measured with spectrophotometer (from reference) was divided with corrected Abs600 to get the conversion factor.

Figure 4. Calibration #2 workflow. (Source: iGEM 2018 InterLab Protocol)

•Calibration #2: this calibration is aimed to obtain particle (i.e. microspheres with similar properties to cells) standard curve so it can be used to estimate the cells number in given samples from their Abs600. First, we made microspheres stock solution by adding 904 uL ddH2O to vortexed 96 uL microspheres with known concentration. We prepared 100 uL ddH2O in each well from second until twelfth column, first until fourth row of 96-well plate. We also created four replicates from microspheres stock solution in the first column (each well contains 200 uL solution). We then made a serial dilution for each replicate by transferring 100 uL from first into second column, mixing it thoroughly, and so on until we discarded 100 uL from eleventh column (i.e. twelfth column only contain pure ddH2O). As soon as each well had been remixed, Abs600 of the samples were measured and recorded in Excel. (Figure 4)

Figure 5. Calibration #3 workflow. (Source: iGEM 2018 InterLab Protocol)

•Calibration #3: this calibration is aimed to obtain fluorescence (i.e. fluorescein with similar properties to GFP) standard curve so it can be used to estimate fluorescence of cell-based measurements (in Part II) from equivalent fluorescein concentration. First, we made 1x fluorescein stock solution (10 uM) by diluting spun-down fluorescein in 1x PBS with appropriate volume. We then created four replicates of 1x fluorescein stock solution and serial dilution in 96-well plate similar with Calibration #2 protocol. Fluorescence for each sample were measured with “BLUE” settings in our plate reader: 490 nm excitation, and 510-570 nm emission. The data obtained were recorded in Excel. (Figure 5)

Part II: Cell Measurements

This part of protocol is aimed to measure Abs600 and fluorescence of transformed Escherichia coli strain DH5α with devices provided from 2018 DNA Distribution Kit Plate. All devices are in plasmid pSB1C3, which carries a gene for chloramphenicol resistance. iGEM Registry of Standard Biological Parts (link) provides detailed information about devices being transformed in this study (Figure 6).

Figure 6. Details about devices used in 2018 InterLab Study: (top row, left to right) positive control, negative control; (middle row, left to right) Test Device 1-3; (bottom row, left to right) Test Device 4-6. (Source: parts.igem.org)

•Positive control contains promoter J23151 with GFP construct (part number: BBa_I20270).

•Negative control only contains TetR repressible promoter without GFP construct (part number: BBa_R0040).

•Test device 1 contains promoter J23101 with GFP construct (part number: BBa_J364000).

•Test device 2 contains promoter J23106 with GFP construct (part number: BBa_J364001).

•Test device 3 contains promoter J23117 with GFP construct (part number: BBa_J364002).

•Test device 4 contains promoter J23100 with GFP construct (part number: BBa_J364007).

•Test device 5 contains promoter J23104 with GFP construct (part number: BBa_J364008).

•Test device 6 contains promoter J23116 with GFP construct (part number: BBa_J364009).

Figure 7. Cell measurements workflow. (Source: iGEM 2018 InterLab Protocol)

The workflow for this part is shown in Figure 7. First, we transformed each device into Escherichia coli strain DH5α according to our laboratory’s protocol (full version please refer to this file) and subsequently plated into different LB agar with chloramphenicol (Cam). After overnight incubation at 37oC, two colonies from each transformation plates were inoculated in 10 mL LB liquid medium + Cam and let to be grown overnight at 37oC and 220 rotations per minute (rpm). On the next day, we diluted 0.5 mL of each culture in 4.5 mL LB + Cam (ratio 1:10) and measured for their respective Abs600, along with Abs600 of LB + Cam (we created two replicates to be measured for each sample). Using obtained Abs600 data, the cultures were further diluted to target Abs600 0.02 in final volume of 12 mL LB + Cam in different 50 mL Falcon tubes covered with foil. From each Falcon tube, 500 uL diluted cultures were sampled and measured for Abs600 and fluorescence, while the rest of diluted cultures were incubated at 37oC, 220 rpm until next six hours to be sampled and measured again. Samples for Abs600 and fluorescence

measurements were put in 96-well plates (each well contains 100 uL volume) according to layout shown in Figure 8, under same conditions as previous calibration in Part I of the protocol.

Figure 8. Layout for Abs600 and fluorescence measurement. (Source: iGEM 2018 InterLab

Protocol)

Part III: Colony Forming Units (CFUs)

This last part of protocol is aimed to convert OD600 (obtained after transformation of Abs600 from Part II with conversion factor from Part I) into CFUs. The significance of this part is that CFU counts are directly correlated with cell concentration in given volume of culture (i.e. viable cell counts per mL). In this part, we used two colonies from each positive and negative control (four in total). This part consists of three steps as follows:

Figure 9. Layout of 96-well plate used for starting sample preparation. (Source: iGEM 2018 InterLab Protocol)

•Step #1: Preparation of starting sample. First, we sampled 25 uL of each positive and negative overnight cultures and diluted them with 175 uL fresh LB + Cam (eight-fold

dilution). We then measured their respective Abs600 along with blank LB + Cam according to layout shown in Figure 9, red inset. Using this data, their OD600 were calculated by multiplying each of them with conversion factor (obtained from Part I). The overnight cultures were further diluted to target OD600 0.1 using previous calculated OD600 data in final volume of 1 mL LB + Cam (these are “starting samples”). We then created triplicates of each starting sample (twelve in total) and checked for their OD600 if they were 0.1, using measurement with same 96-well plate (Figure 9, green inset).

Figure 10. Suggested workflow for serial dilution of starting sample. (Source: iGEM 2018

InterLab Protocol).

•Step #2: Serial dilution of starting sample. Originally, we wanted to conduct exact workflow as shown in Figure 10. However, we realized the maximum capacity of our microtubes was 1.5 mL so we could not aliquot 1.9 mL LB + Cam in the tubes. Therefore, to compensate that issue, we first prepared 36 microtubes with 950 uL LB + Cam each, 24 microtubes with 900 uL LB + Cam each, and 36 LB agar + Cam. For first three dilutions, we halved the volume of LB + Cam in “Dilution 1” until “Dilution 3” tubes and the added volume of starting sample (50 uL into next 950 uL LB + Cam) so the net dilution factor would be the same (20-fold). Finally, we took 100 uL from each last three dilutions to be spread on different LB agar plate + Cam. The plates were then incubated overnight at 37oC and the colonies formed on each plate were counted after 18-20 hours of growth.

•Step #3: Calculation of CFU/mL for OD600 0.1. This calculation assumes that one bacterial cell gives rise to one colony. For OD600 0.1, CFU/mL culture can be calculated by multiplying number of colonies (we used plates with less than 300 colonies in Step #2) with their respective final dilution factors.

Results and Discussions

For complete raw data of calibrations (in Part I) and Abs600 and fluorescence measurement (in Part II), please refer to our Excel file attached here.

Part I: Calibration

Table 1. OD600 reference point results.

	Replicate			Abs600
				LUDOX CL-X			ddH2O
1				0.160			0.104
2				0.157			0.100
3				0.155			0.087
4				0.151			0.093
	Arithmatic mean			0.156			0.096
	Corrected Abs600			0.059
	Reference OD600			0.063
	OD600/Abs600			1.059

When measured with our plate reader, mean Abs600 of LUDOX CL-X was 0.156 and mean Abs600 of ddH2O was 0.096 (Calibration #1). By subtracting the means, we obtained the corrected Abs600 value was 0.059. After dividing the reference OD600 (0.063, provided in Excel file) with corrected Abs600, we found that the conversion factor was 1.059 (Table 1). In other words, when we wanted to transform Abs600 value measured by our plate reader into OD600, we must multiply the Abs600 data with 1.059.

Abs600

Particle Standard Curve

	1.000
	0.800	y = 3E-09x + 0.0783
		R² = 0.9945
	0.600
	0.400
	0.200
	0.000

0.00E+00

5.00E+07

1.00E+08

1.50E+08

2.00E+08

2.50E+08

Particle Count / 100 uL

Particle Standard Curve (log scale)

Abs600

1.000
1.00E+05	1.00E+06	1.00E+07	1.00E+08

	0.100	y = 0.0006x0.3536
		R² = 0.8819

0.010

Particle Count / 100 uL

Figure 11. Particle standard curve results.

Particle standard curves we obtained after conducting Calibration #2 are shown in Figure

11.The equation for particle standard curve was y = 3*10-9x + 0.078 (R2 = 0.9945) and for particle standard curve in log scale was y = 6*10-4x0.3536 (R2 = 0.8819), with x is particle count per 100 uL sample and y is Abs600. As shown in the graphs, the values measured form a straight line and the slope is close to 1:1 until it saturates at low concentration of microspheres.

At medium-high concentrations of microspheres (i.e. from 7.35*106 until 1.18*108 particles/100 uL), we found the mean particle concentration after divided by their respective Abs600 was 2.08*108 particles/100 uL sample. We would later use this value to estimate molecules of equivalent fluorescein (MEFL) per particle in Part II (i.e. in this case, the particles were bacterium cells, and microspheres were used as a representation of the cells). We used medium-high concentrations value because they are less likely to be affected by pipetting error or saturation (the same principle applies to fluorescein which will be discussed later).

Fluorescein Standard Curve

Fluorescence

1.600E+06

1.400E+06

1.200E+06

1.000E+06

8.000E+05				y = 139561x	+ 18723
6.000E+05				R² = 0.9957
4.000E+05
2.000E+05
0.000E+00
0.00	2.00	4.00	6.00	8.00	10.00
		Fluorescein Concentration (uM)

∆������600 �� 10

240

Fluorescein Standard Curve (log scale)

		1.000E+07
		1.000E+06
Fluorescence		1.000E+05
		1.000E+04	y = 176245x0.8822
		1.000E+03	R² = 0.9985
		1.000E+02
		1.000E+01
		1.000E+00
0.00	0.01	0.10	1.00	10.00
		Fluorescein Concentration (uM)

Figure 12. Fluorescein standard curve results.

Our results for fluorescein standard curve after conducting Calibration #3 are shown in Figure 12. The equation for fluorescein standard curve was y = 139561x + 18723 (R2 = 0.9957) and for fluorescein standard curve in log scale was y = 176245x0.8822 (R2 = 0.9985), with x is fluorescein concentration in uM and y is fluorescence in arbitrary units (a.u.). As shown in the graphs, the values measured also form straight line and the slope is close to 1:1.

At medium-high fluorescein concentrations of fluorescein (i.e. from 0.31 until 5 uM), we found the mean concentration of fluorescein after divided by their respective fluorescence level was 5.84*10-6 uM/a.u. When this mean value was converted into MEFL (MEFL/uM fluorescein value is 6.02*1012, provided in the Excel), we found that MEFL per arbitrary unit was 3.52*107. We would later use these values to convert raw data obtained in Part II into fluorescence per OD (uM fluorescein/OD) and fluorescence per particle (MEFL/particle).

Part II: Cell Measurements

Table 2. Mean Abs600 for 1:10 diluted transformed devices. * = calculated by (in uL),

where 240 is target Abs600 (0.02) x target volume (12 mL) and 10 is dilution factor used. TD =

test device.

				Mean			ΔAbs600			Volume Added (Final Volume 12 ml, Abs600 0.02)
	Sample						(Sample-
				Abs600						Overnight Culture (uL)*			LB + Cam (uL)
							Blank)
	Blank (LB + Cam)		0.2355			-			-			-
	Positive Control		0.3775			0.142			169			11831
	Negative Control		0.3365			0.101			238			11762
	TD 1, Culture 1		0.3985			0.163			147			11853
	TD 1, Culture 2		0.3895			0.154			156			11844
	TD 2, Culture 1		0.3625			0.127			189			11811
	TD 2, Culture 2		0.3725			0.137			175			11825
	TD 3, Culture 1		0.3055			0.070			343			11657

TD 3, Culture 2	0.3215	0.086	279	11721
TD 4, Culture 1	0.401	0.1655	145	11855
TD 4, Culture 2	0.3845	0.149	161	11839
TD 5, Culture 1	0.3675	0.132	182	11818
TD 5, Culture 2	0.3535	0.118	203	11797
TD 6, Culture 1	0.3335	0.098	245	11755
TD 6, Culture 2	0.3415	0.106	226	11774

First, we created samples of 1:10 dilution from each transformed device and checked for their respective Abs600 by creating two replicates from each diluted sample. The absorbance result is shown in Table 2, second column. Using the dilution formula, we obtained volume of each initial culture to be added into fresh LB + Cam to target Abs600 approximately 0.02 and final volume of 12 mL (Table 2, fourth and fifth column). To ensure Abs600 of the newly-made dilutions were about 0.02, we performed Abs600 measurement along with their fluorescence at t = 0 hour. The rest of dilutions were then incubated and after 6 hours, their Abs600 and fluorescence were measured again.

Fluorescence per OD

uM Fluorescein/OD

7.000

6.000

5.000

4.000

0 hour

3.000

6 hour

2.000

1.000

0.000

Negative	Positive	Test	Test	Test	Test	Test	Test
Control	Control	Device 1	Device 2	Device 3	Device 4	Device 5	Device 6

Figure 13. Fluorescence per OD result.

Fluorescence per Particle

MEFL/Particle

200000
180000
160000
140000
120000
100000																																										0 hour
80000
																																										6 hour
60000
40000
20000

0

Negative

Positive

Test

Test

Test

Test

Test

Test

Control

Control

Device 1

Device 2

Device 3

Device 4

Device 5

Device 6

Figure 14. Fluorescence per particle result.

Results of fluorescence per OD and per bacterium cell particle are shown in Figure 13 and Figure 14, respectively. When compared, both graphs look similar in pattern, however fluorescence of tested devices were differed from each other. Therefore, it can be implied that some promoters may have different activity in expressing its downstream genes (in this case, GFP). The data at t = 0 hour suggested that promoter J23101 (Test Device 1), J23100 (Test Device 4), and J23104 (Test Device 5) have higher activity in expressing GFP, resulting in higher fluorescence per OD and per particle compared to positive control. Furthermore, fluorescence observed in Test Device 2 and 6 were comparable with positive control, implying that promoter J23106 (Test Device 2) and J23116 (Test Device 6) have similar activity in expressing GFP with promoter J23151 (positive control). On the other hand, there was no fluorescence observed in Test Device 3 (similar with negative control that does not have GFP construct). It is likely that promoter J23117 (Test Device 3) failed to initiate GFP expression.

At t = 6 hour, declines in fluorescence per OD and per particle were observed in positive control, Test Device 2, Test Device 4, and Test Device 6, compared with t = 0 hour. A probable explanation for this phenomenon is that GFP expression mediated by promoters carried by these devices is limited by cell density (i.e. no additional GFP expression when cells in a sample has reached a certain density), or cells in the culture underwent cessation. Therefore, when total fluorescence was divided by the cell number in given sample, fluorescence per OD and per particle will be decreased. Exception for Test Device 1 and 5, increase in fluorescence per OD and per particle were observed, suggesting that promoter J23101 and J23104 may be strong promoters that actively express their downstream genes despite high density of cells.

Part III: Colony Forming Units (CFUs)

100

Table 3. Mean Abs600 for 1:8 diluted transformed devices. * = calculated by ∆����600 �� 8 (in uL),

where 100 is target OD600 (0.1) x target volume (1 mL) and 8 is dilution factor used.

	Sample			Mean			OD600 (Abs600			ΔOD600							Volume Added
																	Overnight
				Abs600			x 1.059)			(Sample-Blank)											LB + Cam (uL)
																	Culture (uL)*
	Blank (LB + Cam)		0.219			0.232						-				-				-
	Positive Control,		0.373			0.395			0.163							77				923
	Culture 1
	Positive Control,		0.386			0.409			0.177							71				929
	Culture 2
	Negative Control,		0.354			0.375			0.143							87				913
	Culture 1
	Negative Control,		0.368			0.390			0.158							79				921
	Culture 2
				Table 4. OD600 measurement from starting samples.
	Sample									Abs600			Mean		OD600 (Abs600						ΔOD600
													Abs600				x 1.059)			(Sample-Blank)
	Blank (LB + Cam), Replicate 1								0.218
	Blank (LB + Cam), Replicate 2								0.216			0.217			0.230					-
	Blank (LB + Cam), Replicate 3								0.217
	Positive Control, Culture 1, Replicate 1								0.316
	Positive Control, Culture 1, Replicate 2								0.316			0.316			0.335					0.105
	Positive Control, Culture 1, Replicate 3								0.315
	Positive Control, Culture 2, Replicate 1								0.311
	Positive Control, Culture 2, Replicate 2								0.310			0.311			0.329					0.099
	Positive Control, Culture 2, Replicate 3								0.312
	Negative Control, Culture 1, Replicate 1								0.308
	Negative Control, Culture 1, Replicate 2								0.307			0.307			0.325					0.095
	Negative Control, Culture 1, Replicate 3								0.307
	Negative Control, Culture 2, Replicate 1								0.316
	Negative Control, Culture 2, Replicate 2								0.314			0.315			0.334					0.104
	Negative Control, Culture 2, Replicate 3								0.314

We created 1:8 dilution from two positive control samples and two negative control samples (obtained after overnight incubation in Part II) and measured for their Abs600 (Table 3, second column). Next, we converted Abs600 data into OD600 by multiplying them with 1.059 (i.e. conversion factor obtained from Part I). From this, we calculated for overnight culture volume to be added into fresh LB + Cam to target OD600 0.1 and final volume 1 mL using dilution formula (Table 3, fifth and sixth column). We then checked Abs600 from newly-made dilutions whether their OD600 were around 0.1 after subtracted by blank. The results is shown in Table 4.

Figure 15. Representation of dilutions grown in LB + Cam agar. (Top row, from left to right) 8 x 104, 8 x 105, and 8 x 106 dilution of positive control. (Bottom row, from left to right) 8 x 104, 8 x 105, and 8 x 106 dilution of negative control.

Table 5. Colony count results. TNTC = too numerous to count (>300 colonies). N/A = not

calculated due to out of optimal 50-200 colony count range.

Colony Count

Estimated CFU/mL (Colony

Mean

Sample

Count x Dilution Factor)

CFU/mL

8 x 104

8 x 105

8 x 106

8 x 104

8 x 105

8 x 106

Positive Control,

TNTC

130

12

N/A

1.04 x 108

N/A

Culture 1, Replicate 1

Positive Control,

TNTC

136

14

N/A

1.09 x 108

N/A

1.05 x

Culture 1, Replicate 2

108

Positive Control,

TNTC

129

15

N/A

1.03 x 108

N/A

Culture 1, Replicate 3

Positive Control,

TNTC

151

16

N/A

1.21 x 108

N/A

Culture 2, Replicate 1

Positive Control,

TNTC

157

18

N/A

1.26 x 108

N/A

1.25 x

Culture 2, Replicate 2

108

Positive Control,

TNTC

162

19

N/A

1.30 x 108

N/A

Culture 2, Replicate 3

	Negative Control,	TNTC	76	6	N/A	6.08 x 107	N/A
	Culture 1, Replicate 1
	Negative Control,	TNTC	82	8	N/A	6.56 x 107	N/A	6.16 x
	Culture 1, Replicate 2							107
	Negative Control,	TNTC	73	7	N/A	5.84 x 107	N/A
	Culture 1, Replicate 3
	Negative Control,	TNTC	91	10	N/A	7.28 x 107	N/A
	Culture 2, Replicate 1
	Negative Control,	TNTC	83	9	N/A	6.64 x 107	N/A	6.69 x
	Culture 2, Replicate 2							107
	Negative Control,	TNTC	77	9	N/A	6.16 x 107	N/A
	Culture 2, Replicate 3

We performed serial dilution as suggested in iGEM 2018 InterLab Protocol from the dilutions and the results is shown in Figure 15 and Table 5. Based on plates with optimal colony count (i.e. 50-200 colonies), we found that estimated CFU concentration per 0.1 OD600 of positive control culture 1, positive control culture 2, negative control culture 1, and negative control culture 2 were approximately 1.05 x 108, 1.25 x 108, 6.16 x 107, and 6.69 x 107 CFUs/mL, respectively (Table 5, eighth column).

Conclusions

Table 6. Manual conversion of fluorescence per OD into fluorescence per CFU, compared with

fluorescence per particle.

Finally, we tried to manually convert our obtained fluorescence per OD (in Part II) into fluorescence per CFU using estimated CFU concentration per 0.1 OD600 (in Part III), and compared them with our obtained fluorescence per particle (in Part II). The analysis for t = 0 hour can be seen in Table 6 (detail calculation can be found in our Excel file). We found that our calculated fluorescence per CFU were different with fluorescence per particle. Therefore, our results suggested that the benefit of using direct method in expressing total cell number such as colony forming units (CFUs) than OD in reporting fluorescence per cell remains doubtful. However, to validate our findings, additional data from another teams are necessary.