Difference between revisions of "Team:Edinburgh OG/InterLab"

Line 1: Line 1:
 
{{Edinburgh_OG}}
 
{{Edinburgh_OG}}
 
<html>
 
<html>
−
 
+
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;
 
<h1>InterLab</h1>
 
<h1>InterLab</h1>
  

Revision as of 13:17, 17 October 2018

PhagED: a molecular toolkit to re-sensitise ESKAPE pathogens

     

InterLab

Introduction

One of the key components to iGEM and synthetic biology in general is standardisation. For now five years, iGEM has developed a robust measurement procedure that allows iGEM teams to measure the fluorescence of green fluorescent protein (GFP). The InterLab aims to identify and correct the sources of systematic variability in synthetic biology by giving all participating labs a protocol for measuring GFP fluorescence. This year’s experiment wanted to look at reducing the variability between labs in measuring fluorescence by normalising absolute cell count instead of OD600. The InterLab used eight plasmids (BBa_R0040, BBa_I20270, BBa_J364000, BBa_J364001, BBa_J364002, BBa_J364007, BBa_J364008, and BBa_J364009) to measure OD600 and GFP fluorescence.

Materials and Methods

Platereader we used was the FLUOstar Omega BMG Labtech. Specs:
  • Bandwitdth was 530/30 nm
  • 485 nm excitation
  • 520 emission>
  • 829 gain
  • It read plates from the top

Competent Escherichia coli DH5α strain were created and transformed using iGEM’s protocols.
InterLab Protocol can be found here.

Results and Discussion

Calibration 1: OD600 Reference point - LUDOX Protocol

LUDOX CL-X (45% colloidal silica suspension) and water replicates were pipetted into a plate to get an absorbance reading. These readings were used to create a ratio to convert absorbance to OD.

Table 1. LUDOX CL-X and water Replicates Absorbance at 600 nm used to create OD600/Abs600 ratio.

Calibration 2: Particle Standard Curve - Microsphere Protocol

Monodisperse silica microspheres have characteristics that are similar to the size and shape of cells while also having a known amount of particles in a certain volume. A standard curve of particle concentration was created to later be used to estimate a number of cells from Abs600.

Figure 1. Particle standard curve created by measuring Absorbance at 600 nm of a series dilution of monodisperse silica microspheres.

Figure 2. Particle standard curve in logarithmic scale created by measuring Absorbance at 600 nm of a series dilution of monodisperse silica microspheres.

Calibration 3: Fluorescence Standard Curve - Fluorescein Protocol

Fluorescein was used to creat a standard curve for fluorescence as using GFP protein with all of the participating teams would be expensive. Figure 3 and Figure 4 show our results.

Figure 3. Fluorescein standard curve created by measuring Fluorescence of a series dilution of fluorescein.

Figure 4. Fluorescein standard curve created by measuring Fluorescence of a series dilution of fluorescein.

Results and Discussion

Colony forming unit per 0.1 OD600 E. coli cultures

Replicates of a starting overnight cultures were all diluted to OD600 and then serial diluted and plated. CFUs (colony forming units) were counted and assuming 1 bacterial cell will give rise to 1 colony, number of CFUs should directly correlate to concentration of cell culture. Figure 5 show our results.

Figure 5. Estimated CFU in a starting 1 ml sample of OD600 = 0.1. 1.1-4.3 are replicates of BBa_R0040 and BBa_I20270 which are the positive (1.1-2.3) and negative controls (3.1-4.3) respectively. CFU/mL was calculated by dividing the colonies formed on plates by its dilution factor. D4 is a dilution factor of 1/(8x105,) and D5 is a dilution factor of 1/(8x106).

Figure 6. Fluorescence measurements of colonies taken at 0 hours and 6 hours. Colonies show wide variability of fluorescence with notably colony 2 of negative control showing fluorescence likely suggesting there was have been contamination from one of the other colonies or the Edinburgh_UG team.

Figure 7. Absorbance600 measurements of colonies taken at 0 hours and 6 hours. Colonies show a range of 0D600 from 0.2 to 0.37. However there does not seem to be any link between OD600 at 0 hours or at 6 hours.

Conclusion

Looking at our data, we can see that our data suggest that the amount of cells in a 1 mL culture is between 60,000,000 and 100,000,000. Our Dilution 4 data estimates the number of cells to be much lower than our dilution 5 data almost by half.