General Concept

In order to determine a peptide with affinity to a molecule of interest an iterative process of affinity binding and washing, called panning, is needed to yield an end result with a high concentration of high affinity peptides.

Figure 1: Flowchart over the workflow of a typical phage display screening

New Application

With the experiment necessitating the use of phage display on an entire organism, no existing protocol was entirely applicable. This meant that we had to adapt a protocol as much as it was possible and introduce completely new solutions to problems unique to our application.

For a detailed description of our protocol click here. Our whole organism phage display experiments started with preparation of the containers that the whole procedure were performed in microcentrifuge tubes with filter inserts. The preparation consisted of blocking the tubes with blocking buffer to prevent non-specific interactions.
To avoid selecting for phage with affinity for the plastic and not the organism, an affinity screening for the tubes was performed before introducing the target. After collecting the phage elute that doesn’t bind to the tubes, we performed our first affinity screening against the small strongyle. This was done by introducing the 12-mer peptides expressing phages to the strongyle placed in the filter tubes. Unbound phages were then washed away followed by elution and collection of the bound phages with an general buffer. All washing and elution steps were performed in the filter tubes, where liquid during centrifugation could pass through the filters, leaving the strongyle still on the top of the filter.

Figure 1: Filter tube blocked with Blocking Buffer.

Figure 2: The strongyles are added, exess liquid spun down and discarded.

Figure 3: Phages are added, left to incubate in solution with the worms. The unbound phages are spun down and discarded. The bound phages are subsequently eluted with a acidic buffer

In the next step of the experiment, phage titering was carried out, to visualise the amount of infectious phages present in the elute. The elute phage with affinity to the strongyle were then amplified in the E.coli ER2738 host strain, by adding the phage to the strain in early log-phase.
Phage and bacterias were then separated with the help of centrifugation to discard E. coli and the phage were extracted by precipitation.
The success of the amplification was examined by a new round of phage titering. Once aware of the phage titer, the next round of this previously described procedure consisting of affinity screening to the strongyle, washing and elution, phage titering, amplification of phage and a new round of phage titering was performed.

After the third round of affinity screening, single plaques, (consisting of single phage clones) were picked from the titering plates and amplified separate. The phages DNA from the amplified plaques were then extracted and purified.

Phage Titering

Phage titering is done after every affinity screening to assess the amount of phages that bind to the target. By following the titering protocol consisting of plating phages together with mid-log phase bacteria visible blue plaques are formed on Xgal/IPTGl plates. The goal with plating is to achieve plates with around 100 plaques, which is fulfilled by doing several dilution series of the infected bacteria. The reason for this is that plaques will only increase linearly with added phages when the multiplicity of infection (MOI) is much less than 1. Also low MOI result in one DNA sequence per plaque. To asses the titre, plaque forming unit (pfu) can be calculated by multiple numbers of plaques with the bacteria dilution.

Phage titering is also carried out after every phage amplification in order to assess the success of the amplification and to make sure a sufficient amount of phages for the subsequente affinity screening are present.

We did three rounds of panning to select for phages having affinity peptides for the target. The last phage titering could then be used to select single clones to be prepared for sequencing.

Verifying the Affinity and Analysis of DNA

So how do we prove that the selected phages clones really binds to our target? With the help of ELISA (enzyme-linked immunosorbent assay) single phage clones affinity to the target could be tested by screening against plastic binders. This allowed us to determine which samples are viable. The ELISA was performed in the centrifugal filter-tubes as to expose the phages to the same environment as the panning stage of the process.

After amplification of each chosen plaque, the phage DNA was extracted an analyzed before sequencing. We used a nanodrop to determine the DNA concentration and gel electrophoresis to determine the purity and the size of the DNA.