Difference between revisions of "Team:Uppsala/Worm Culturing/Experiment"

Line 460: Line 460:
 
The worm and debris solution is inserted in the pasteur pipette and is left above the cotton filter for a time between 30 minutes and 1 hour. In this time  the nematodes get to swim through the filter, while larger impurities are stopped. The solution recovered was pure enough to proceed to the sterilization step. <br><br>
 
The worm and debris solution is inserted in the pasteur pipette and is left above the cotton filter for a time between 30 minutes and 1 hour. In this time  the nematodes get to swim through the filter, while larger impurities are stopped. The solution recovered was pure enough to proceed to the sterilization step. <br><br>
  
<h2>Nematode sterilization</h2><br><br>
+
<h2>Nematode sterilization</h2>
  
The purified worm solutions have undergone sterilization. This was done for the following phage display and co-culturing. In the co-culturing, If the sterilization step is not done or is insufficient, it could lead to upregulation of other genes than those that are under investigation, which in turn would lead to the accumulation of false positives. Therefore this step is fundamental. <br><br>
+
<p>The purified worm solutions have undergone sterilization. This was done for the following phage display and co-culturing. In the co-culturing, If the sterilization step is not done or is insufficient, it could lead to upregulation of other genes than those that are under investigation, which in turn would lead to the accumulation of false positives. Therefore this step is fundamental. <p>
 +
<p>The sterilization was done by applying a solution of bleach to the nematodes. The concentration of bleach was kept at a sufficient level so that the nematodes survived and the bacteria died. After the sterilization washes was made with sterile physiological solution (saline). This led to the removal of the bleach and created a sterile environment in which the nematodes could survive. <p>
 +
<p>In order to make sure that the sterilization had succeeded a control was made by putting an aliquot of the sterilized worm solution into a small flask of LB. This was then put into incubation overnight. If nothing had started growing in the flask sufficient sterilization had been achieved. An example of this can be seen below in figure X where the sample that was put into the rightmost flask was shown to be sterile while the others was not. <p>
  
The sterilization was done by applying a solution of bleach to the nematodes. The concentration of bleach was kept at a sufficient level so that the nematodes survived and the bacteria died. After the sterilization washes was made with sterile physiological solution (saline). This led to the removal of the bleach and created a sterile environment in which the nematodes could survive. <br><br>
+
<p><img src="https://static.igem.org/mediawiki/2018/1/14/T--Uppsala--Figure3horsefeces.png" height="70%" width="70%">
In order to make sure that the sterilization had succeeded a control was made by putting an aliquot of the sterilized worm solution into a small flask of LB. This was then put into incubation overnight. If nothing had started growing in the flask sufficient sterilization had been achieved. An example of this can be seen below in figure X where the sample that was put into the rightmost flask was shown to be sterile while the others was not. <br><br>
+
Figure 4: shows the result from a sterilization test. The aliquote that was put into the rightmost flask proved to be sterile.<br>
  
<img src="https://static.igem.org/mediawiki/2018/1/14/T--Uppsala--Figure3horsefeces.png" height="70%" width="70%">
+
<h2>Nematode separation</h2>
Figure 4: shows the result from a sterilization test. The aliquote that was put into the rightmost flask proved to be sterile.<br><br>
+
  
<h2>Nematode separation</h2><br><br>
+
<p>To investigate the possibility of adapting the workflow of the development of the diagnosis tool for small strongyles to large strongyles, samples containing uniquely large strongyles is needed. <p>
 +
<p>Since small strongyles can be present in horses without large strongyles, but the opposite doesn’t occur, a system to separate the two types of strongyles was needed. The only pre-existing system employed by researchers that intend to collect nematodes of a certain class is the use of a pick under a microscope. This however is very time consuming and doesn’t allow obtaining a high concentration of nematodes and therefore a different procedure was needed. With this goal a microfluidic chip has been created. <p>
  
To investigate the possibility of adapting the workflow of the development of the diagnosis tool for small strongyles to large strongyles, samples containing uniquely large strongyles is needed.<br><br>
 
Since small strongyles can be present in horses without large strongyles, but the opposite doesn’t occur, a system to separate the two types of strongyles was needed. The only pre-existing system employed by researchers that intend to collect nematodes of a certain class is the use of a pick under a microscope. This however is very time consuming and doesn’t allow obtaining a high concentration of nematodes and therefore a different procedure was needed. With this goal a microfluidic chip has been created. <br><br>
 
  
 
+
<p>The chip presented a single channel that splits in 2. The solution containing both types of nematodes, and any kind of contaminant, can be pumped inside the single channel. 2 valves, connected to the 2 split channels, can be used to redirect the flow from the main channel to one of the 2. Positioning this chip under a microscope, and analysing a strongyle when reaching the bifurcation allows the determination of the nature of the nematode. The flow is then directed towards the collection tubes. <p>
The chip presented a single channel that splits in 2. The solution containing both types of nematodes, and any kind of contaminant, can be pumped inside the single channel. 2 valves, connected to the 2 split channels, can be used to redirect the flow from the main channel to one of the 2. Positioning this chip under a microscope, and analysing a strongyle when reaching the bifurcation allows the determination of the nature of the nematode. The flow is then directed towards the collection tubes. <br><br>
+
<p>This system, even though it doesn’t allow an immediate separation of all the large strongyles from the sample, leads to a quicker separation compared to hand picking. A low flow pump, such as a pressure or a syringe pump, is required. These details are described in the protocol we developed.<br>
This system, even though it doesn’t allow an immediate separation of all the large strongyles from the sample, leads to a quicker separation compared to hand picking. A low flow pump, such as a pressure or a syringe pump, is required. These details are described in the protocol we developed.<br><br>
+
  
 
<h2>Co-culturing</h2><br><br>
 
<h2>Co-culturing</h2><br><br>

Revision as of 13:37, 15 October 2018