Measure what is measurable, and make measurable what is not so.
-- Galileo Galilei
Most of our data were obtained by measuring the expression of reporters in platereader experiments. In the first attempts, we failed to obtain reproducible data by applying workflows that are commonly used for E. coli. We realized that a new chassis requires overthinking existing procedures and we decided to establish a workflow for platereader experiments tailored to V. natriegens which respects species specific properties, primarily its unbeaten doubling time.
When first following this approach with V. natriegens, we realized that a different workflow is needed for the worlds fastest growing organism. We tested how much V. natriegens grows during the preparation of a full 96 well plate. We set up an experiment using a stationary culture of V. natriegens with a plasmid weakly expressing lux - to achieve realistic conditions - and diluted this culture 1 : 100 in a 96 well plate with one pipetting step taking 30 seconds. The result of this experiment can be seen in figure 1.
The data show an obvious trend towards higher OD600 for wells that were pipetted first. Seemingly, V. natriegens is able to recover from stationary phase and undergo almost one cell division in 45 minutes at room temperature. Please note that performing this experiment with a culture in the exponential phase, as described in some E. coli protocols, would most likely result in an even stronger trend.
With this in mind, we managed to establish a workflow that omits measuring and independently diluting individual wells.
We tested to cultivate our precultures - inoculated from glycerol stocks - directly in 96 well plates and incubated this plate for five to six hours in a platereader or shaking incubator. For V. natriegens, this time frame is sufficient for all cultures to reliably reach stationary phase which equals an overnight culture for E. coli. The cultures are then diluted in two steps: 1:50 and 1:40, finally resulting in a 1:2000 dilution of the preculture. Compared to the commonly used workflows for E. coli, our approach does not consider the OD600 of individual wells but instead dilutes all cultures by the same factor.
The OD600 after 1:50 dilution of the 96 well plate is shown in figure 2. Despite not calculating dilutions for individual wells, the range of values is explicitly smaller and additionally no positional bias can be observed.
A
BHeterogeneity of 96 well plate after preparation
A) One pipetting step each 30 s, starting with A1
B) Intermediate dilution (1:50) of a preculture
Besides the experimental workflow, we established an approach for fast and accurate data analysis. From a mathematical point of view, constant expression and constant degradation result in a steady state level of a molecule. In the context of bacterial reporter experiments, the molecule is a reporter protein or enzyme and the steady state level. That represents a constant signal to OD600 ratio, meaning a constant reporter concentration in the growing cells. For a stable reporter, constant degradation is actually due to dilution by cell division. Thus, the degradation rate mainly depends on the growth rate.
To conclude, we assumed that a constant signal to OD600 ratio is achieved throughout the exponential phase since the growth rate, as well as the expression from constitutive or constantly induced promoters remains stable.
With this in mind, we aimed to create an algorithm identifying the exponential growth phase and calculating the signal to OD600 ratio. In our first experiments we tried to identify a point in time at which all cultures grow exponentially, and failed. We were not able to obtain reproducible data for two reasons. Firstly, cultures grow differently, depending on the starting concentration and fitness differences caused by varying test constructs and expression strengths. Secondly, individual measurements are highly variable (we saw this especially for OD600 measurements). Therefore performing calculations with a single value is highly susceptible to outliers.
The threshold is indicated with a dotted line at OD600 = 0.2. The time point that first exceeded 0.2. is shown in red and the data points that are included in the range are displayed in green. The mean of the luminescence/OD600 ratio of all points is calculated to assign a value to this well.
The mean CV of all wells over the three independent experiments for each combination of OD600 threshold and range is shown on the Z-axis
Consequently, every result (e.g. promoter strength) is, in total, the mean of 84 measurements. This high number of raw data leads to a high degree of reproducibility and, as we believe, to highly accurate characterization data.
The choice of 0.2 as the OD600 threshold and the range of three time points was not randomly chosen but selected after calculating the mean CV for combinations of OD600 thresholds and ranges. We tested OD600 thresholds ranging from 0.1 to 0.6 with a step size of 0.01 and ranges around this data point from 0 to 10. Please note that the range is applied double-sided, meaning that a range of 10 considers 10 data points before and after a well has reached the OD600 threshold resulting in averaging 21 time points.
The threshold indicates the OD600 value which has to be reached by each individual well to determine the values considered for analyzation. The range sets the number of time points before and after the well reached the threshold that are used for mean calculation.
The mean CV of all wells over the three independent experiments for each combination of OD600 threshold and range is shown on the Z-axis
As discussed previously, expression data can be assumed to be constant throughout the exponential growth phase. To our experience, the cultures leave the full exponential phase around OD600 = 0.5 - 0.6 resulting in a divergence from the previously constant luminescence/OD ratio which leads to a loss of reproducibility for high OD600 thresholds. Slightly higher CT values can also be observed for very low OD thresholds. We noted that the OD600 fluctuates significantly when measuring very low cell concentrations, presumably due to technical inaccuracies. This effect can drastically effect data points for low OD 600 values (<0.1). Generally, we consider using a high range useful because this increases the number of data points that are averaged, thus decreasing the impact of single outliers. However, for a fast growing organism like V. natriegens, the time of a culture with a OD600 high enough to yield reliable measurement results but low enough to be exponentially growing is limited. Therefore an excessive range leads to inclusion of either too low or too high data points, which again reduces reproducibility.
We consider this analysis as a foundation for the selection of the OD600 threshold 0.2 and a range of 3 that was used in the analysis of all our plate reader experiments. This enabled us to achieve high reproducibility of our data from three subsequent, independent experiments.
clear all close all %% Import Platereader raw data Lux_Data_raw_Day1 = xlsread('Connector_Lux_071018.xlsx','All Cycles'); OD_Data_raw_Day1 = xlsread('Connector_OD_071018.xlsx','All Cycles'); Lux_Data_raw_Day2 = xlsread('Connector_Lux_071018_2.xlsx','All Cycles'); OD_Data_raw_Day2 = xlsread('Connector_OD_071018_2.xlsx','All Cycles'); Lux_Data_raw_Day3 = xlsread('Connector_Lux_081018.xlsx','All Cycles'); OD_Data_raw_Day3 = xlsread('Connector_OD_081018.xlsx','All Cycles'); %% Merge all data in two matrices OD_Data(:,:,1) = OD_Data_raw_Day1; OD_Data(:,:,2) = OD_Data_raw_Day2; OD_Data(:,:,3) = OD_Data_raw_Day3; Lux_Data(:,:,1) = Lux_Data_raw_Day1; Lux_Data(:,:,2) = Lux_Data_raw_Day2; Lux_Data(:,:,3) = Lux_Data_raw_Day3; %% Blank substraction and cut off for h = 1:size(Lux_Data,3) for k = 1:size(Lux_Data,2) Blank = mean(Lux_Data([60,72,84,96],k,h)); for j = 1:size(Lux_Data,1) Lux_Data(j,k,h) = Lux_Data(j,k,h)-Blank; if Lux_Data(j,k,h) < 50 Lux_Data(j,k,h) = 50; % Cut off for Lux signal end end end end for h = 1:size(OD_Data,3) for k = 1:size(OD_Data,2) Blank = mean(OD_Data([60,72,84,96],k,h)); for j = 1:size(OD_Data,1) OD_Data(j,k,h) = OD_Data(j,k,h)-Blank; if OD_Data(j,k,h) < 0.01 OD_Data(j,k,h) = 0.01; % Cut off for OD end end end end %% Calculating ratio around OD 0.2 Ratios = zeros(size(OD_Data,1),1,3); for q = 1:size(OD_Data,3) % looping over days for o = 1:size(OD_Data,1) % looping over samples for p = 1:size(OD_Data,2)-3 % looping through time points if OD_Data(o,p,q) > 0.2 && OD_Data(o,p+1,q) > 0.2 && Ratios(o,q) == 0 Ratios(o,q) = mean(Lux_Data(o,p-3:p+3,q)./OD_Data(o,p-3:p+3,q)); end end end end %% Calculating mean and std of individial samples for k = 1:12 Samples(k,1,1:3) = mean(Ratios([k,k+12,k+24,k+36],:)); % calculate mean of technical triplicates Samples(k,2,1:3) = std(Ratios([k,k+12,k+24,k+36],:)); % calculate std of technical triplicates end for k = 13:24 Samples(k,1,1:3) = mean(Ratios([k+36,k+48,k+60,k+72],:)); % calculate mean of technical triplicates Samples(k,2,1:3) = std(Ratios([k+36,k+48,k+60,k+72],:)); % calculate std of technical triplicates end %% Sort samples for top and bottom row Names = {'J23100', '5Con1 long','5Con2 long','5Con3 long','5Con4 long',... '5Con5 long','5Con1 short','5Con2 short','5Con3 short',... '5Con4 short','5Con5 short','5Con1 long','5Con2 long','5Con3 long',... '5Con4 long','5Con5 long','5Con1 short','5Con2 short','5Con3 short',... '5Con4 short','5Con5 short', 'Promoter Dummy'}; Top_row = Samples(1:11,:,:); Bot_row = Samples(13:23,:,:); SortedValues = []; for k = 1:size(Top_row,1) SortedValues = [SortedValues; Top_row(k,:,:); Bot_row(k,:,:)]; end SortedValues = [SortedValues;Samples(12,:,:)]; SortedValues(22,:,:) = []; %% Calculate relativ strength Relative_strength = SortedValues; for h = 1:size(SortedValues,3) for k = 1:size(SortedValues,1) Relative_strength(size(SortedValues,1)-k+1,2,h) = ... Relative_strength(size(SortedValues,1)-k+1,2,h)/Relative_strength(1,1,h); Relative_strength(size(SortedValues,1)-k+1,1,h) = ... Relative_strength(size(SortedValues,1)-k+1,1,h)/Relative_strength(1,1,h); end end %% plot relative strenths figure(1) % constructs with J23100 hold on bar(mean(Relative_strength([1:11,22],1,1:3),3),'facecolor',[125/255,202/255,97/255]) errorbar((mean(Relative_strength([1:11,22],1,1:3),3)),... std(Relative_strength([1:11,22],1,1:3),1,3),'linestyle','none','color','k') set(gca, 'YScale', 'log') ylabel('normalized Luminescence/OD_6_0_0') set(gca,'Color','w') xticks([1:12]) xticklabels(Names([1:11,22])) xtickangle(45) ylim([0.001 3]) yticks([0.001,0.01,0.05, 0.1, 0.5, 1.0, 2.0 ]) yticklabels([0.001,0.01,0.05, 0.1, 0.5, 1.0, 2.0]) figure(2) % constructs with promoter dummy hold on bar(mean(Relative_strength([1,12:22],1,1:3),3),'facecolor',[125/255,202/255,97/255]) errorbar((mean(Relative_strength([1,12:22],1,1:3),3)),... std(Relative_strength([1,12:22],1,1:3),1,3),'linestyle','none','color','k') set(gca, 'YScale', 'log') ylabel('normalized Luminescence/OD_6_0_0') set(gca,'Color','w') xticks([1:12]) xticklabels(Names([1,12:22])) xtickangle(45) ylim([0.001 3]) yticks([0.001,0.01,0.05, 0.1, 0.5, 1.0, 2.0 ]) yticklabels([0.001,0.01,0.05, 0.1, 0.5, 1.0, 2.0])
A
B
C
DPlasmids were built with four different reporters.
A) Lux B) RFP C) sfGFP D) YFP
A
B200 µL of one Lux expressing sample was placed in C3 while all other wells were filled with medium
Data were normalized over the strongest construct ColE1. Error bars represent the standard deviation of the measurements of three independent experiments